Our oblique penholders are hand crafted at our studio.

We try our best to provide a properly adjusted holder for your use.

 

The brass flanges are bent and crimped from equipment made in the early 1900's to create a flange that is perfectly formed that will accept the pen nib easily.

Each flange is hand adjusted to fit specific nib sizes.

 

Garnet Red or Sapphire Blue

Comfort Grip Oblique Pen Holders

 

We are making a new, more comfortable oblique pen holder using the new Speedball holders that are easy-to-hold, have a cushioned grip in two vibrant colors. The flanges are are adjusted to your nib for easy use.

 

7" Garnet Red & Sapphire Blue Speedball Comfort Grip Holders

with brass offset flange to fit various size nibs.

Adjusted for pen nib of your choice please specify color & nib.

$15.95 each

 

7" Garnet Red & Sapphire Blue Speedball Comfort Grip Peerless  Holders without brass flange.

$3.49 each, $3.39 for 6+, $3.29 for 12+

 

 

 

 

Oblique Gray Peerless Pen Holders

7" grey plastic holder with brass offset flange to fit various size nibs

adjusted for pen nib of your choice - please specify nib

$11.75 each

 

Straight Pen Holders - 7" grey plastic

$1.25 each

 

These instructions were developed some years ago

by Stephen A. Ziller, Master Engrosser

and graduate of the Zanerian College in Columbus, Ohio.

 

We still employ these principles today in the pen holders we make for you.

 

If you need help on adjusting, your pen holder, please print this page.

The metal attachment or brass flange on your holder should hold the pen just tight enough to keep it from falling out.

 

If it is too tight, it will bend the pen and cause one nib to be out of place.

If it is too loose, pinch together at point F (the back of the metal flange.

ILLUSTRATION #1 -

For standard size pen points, the pen should be inserted into the metal attachment until it is even with the point indicated - F. (back edge of metal flange)

The point of the pen is in good writing position if the tip is anywhere from A to B (about 1/8" distance left of the center point) as noted on the picture.

Please note that B is on the center line of the holder. (This is when you are looking down onto the top of the pen nib).

ILLUSTRATION #2 -

This is a side view and is meant to show that the pen line which is the slope of the pen point looking at it from the side - is upward from the center line.

Many penmen prefer the point to extend even higher at the left as you look at this picture, but we believe the adjustment shown is better.

 

ILLUSTRATION #3 -

This is one of the most important of all adjustments. The left edge and the right edge of the pen point must line up with the center of the holder. In other words, these three points must be in a straight line.

 

ILLUSTRATION #4 -

This view of the end of the pen holder shows the tip of the point on the center line which would be point B, illustration #1. It shows the L and R lined up with C as in No 3. It shows the point of the pen a little above center as in No 2.

ILLUSTRATION # 5 -

This is the metal attachment removed from the holder. If you desire to be proficient you will probably want to change the angle for smaller and larger pens. With a small pair of pliers, straighten the flanged edge. To make more angle, cut a little off the M end and rebend.

These instructions are applicable for any pointed pen - oblique pen holder made with a flexible brass flange to hold the nib ---- some designs do not allow for these adjustments to be made.

If you accidentally dip the attachment in ink, see that you clean it all out thoroughly before it becomes dry, as this ink will harden and spring your pen point out of shape.

If you want to use a smaller pen point, you will have to adjust your metal attachment and this can be done easiest by placing the desired pen point in the attachment bending round to fit the point and then bending the attachment back slightly which will open the space slightly and keep from binding the pen point. Adjust after this for the result desired in No. 1, 2, & 3. At this point be sure again that the pen does not bind in the metal. For small points you will not be able to insert to the point marked F in No.1 (the back edge of the metal flange).